Quantitation of Amino Acids (2024)

Comprehensive Guide to Hydrolysis and Analysis of Amino Acids

Quantitation of Amino Acids

7.1 INTRODUCTION

7.1 INTRODUCTION

Although this guide generally concentrates on the initial steps of amino acid analysis— emphasizing sample preparation for hydrolysis—this section presents a brief discussion of the more common quantitation approaches used in amino acid analysis. In these examples, the results from amino acid analysis have been obtained; the original sample concentration needs to be calculated. These examples assume that AccQ•Tag or AccQ•Fluor Reagents have been used for the derivatization.

Before proceeding with quantitation:

  • Verify that all peaks are correctly identified.
  • If retention times do not match, check the values in your calibration table.
  • Check for correct integration of all peaks.

7.2ABSOLUTE QUANTITATION OF AMINO ACIDS

7.2ABSOLUTE QUANTITATION OF AMINO ACIDS

7.2.1 Concentration of protein in a sample

7.2.1 Concentration of protein in a sample

For some analyses, the goal is simply to determine the concentration of the analyzed sample. These results are usually expressed in molar concentrations, such as µmol/L. The chromatographic results are typically given in picomoles. To determine the concentration, the picomoles of amino acid reported by the chromatographic software is divided by the injection volume. This value is then multiplied by the volume of diluent divided by the volume derivatized. To complete the calculation, multiply by the dilution factor, and then convert the units to µmoles per liter.

Example calculation:
To determine the concentration of the amino acid in the original sample, based on the reported value, we use the following equation:

Where:

pmol AA = the amount reported for amino acids in sample Vi = injection volume in µL, typically 1 µL

Vd = volume derivatized in µL, typically 10 µL

Vr = volume of diluent used to reconstitute sample in µL Dil. Factor = dilution factor

Example:

An initial 100-µL sample of hydrolyzed protein sample was diluted 1:1 with internal standard. A 10-µL aliquot was derivatized. The injection volume was 1 µI and the reported value was 312.5 pmoles for asparagine (Asn).

The Asn concentration in µmol/L would be:

7.3 RELATIVE QUANTITATION OF AMINO ACIDS

7.3 RELATIVE QUANTITATION OF AMINO ACIDS

Determination of the amino acid composition of a hydrolyzed protein involves calculating the molar ratios of the components within a sample.

Each pure protein has a specific stoichiometric number of residues for each amino acid it contains. Ideally, the results of an analysis yield molar ratios that are integers. The degree to which the observed values approach this ideal is a function of the purity of the protein or peptide, the adequacy of the hydrolysis conditions, and the quality of the amino acid analysis.

7.3.1 Calculation of the compostion of a peptide

7.3.1 Calculation of the compostion of a peptide

Example 1 (as reflected in the table below):

  1. Tabulate theObserved Picomolesfor each amino acid (obtained from analysis).
  2. Estimate the number of residues (Estimated Composition) for each amino acid by inspection.Note:Theobservedresiduesare the relative molar concentration of each aminoacid. Divide all observed picomoles by the least abundant amino acid and roundto the nearest digit.
  3. Sumthe picomoles and the number of residues for all amino acids.
  4. Calculate theAveragepmol/residueby dividing Sum Observed Picomole by Sum Estimated Composition.
  5. Divide each Observed Picomoles by the picomoles/residue value to determine the Observed Composition.

Average pmol/residue

WARNING:For larger proteins, estimation of the number of residues ismoredifficult because of the greater precision required.

WARNING:Recoveryofsomeaminoacidsfromhydrolysismaybevariable(Ser, Tor, Tyr, and Met are subject to degradation; Val and Ile bonds may bedifficulttocleave).

Note:Toimprovequantitationin such cases, it is recommended that a time-coursestudyis performed. Typically, samples are hydrolyzed for 24, 48, and 72 (or 96) hours;labileaminoacidvaluesaredeterminedbyextrapolation back to zero time, while thevaluesfor Ile and Val are taken from the longest hydrolysis.

Example 2:
In some cases, as noted earlier, calculation of the mole percent (the number of residues of each amino acid per 100 residues of protein) may be satisfactory. This is determined as follows:

7.3.2 Estimation of the molecular weight of a protein

7.3.2 Estimation of the molecular weight of a protein

If an estimate of the molecular weight of the protein is available, two approaches can be used to calculate an approximate composition:

7.3.2.1 Composition based on size and total amino acid yield

7.3.2.1 Composition based on size and total amino acid yield

  1. Estimate sample molecular weight (MW).
  2. Sum the total yields of amino acids in picomoles.
  3. Divide the molecular weight by 110, the average MW of amino acids.Note:Thisgivesa good approximation of the total chain lengthortotalaminoacids.
  4. Divide the total yield by the chain length (equals molar amount of sample injected).
  5. For each amino acid, divide the amount by the molar amount injected (equals number of residues per mole). Examine the deviations from integral amounts.
  6. Slightly vary the divisor (molar amount injected) up or down to minimize the deviation from integral amounts (obtained in Step 5). This step can be simplified with a computer spreadsheet program or tailored amino acid software that finds the minimum deviations.
  7. Remember that values for labile amino acids and stable bond formers may deviate significantly from integral amounts due to poor recoveries from hydrolysis.

7.3.2.2 Composition based on normalization to a single amino acid

7.3.2.2 Composition based on normalization to a single amino acid

This alternative procedure requires more knowledge about the sample.

  1. Choose an amino acid in the analysis that meets the following two criteria:
    • Gives good yields upon hydrolysis and derivatization (e.g., Asp, Glu, His, Arg, Ala, Pro, Leu, Phe, Lys). Gly may be a poor choice because it is a common background contaminant; and
    • Can have only a few residues per mole of sample (based on estimated sample molecular weight and amino acid yield). Such information can be obtained from other procedures, such as cyanogen bromide digestion, which cleaves the intact polypeptide chain selectively at methionine.
  2. Based on this information, choose an integral value for this amino acid.
  3. Divide the yield of the selected amino acid by the chosen integral value to get the estimated molar amount of sample injected.
  4. Follow Section 7.3.2.1, Steps 5 and 6.
  5. Check the values (one greater and one less than the chosen integral value) to see if smaller deviations from whole numbers are obtained.

7.3.2.3Calculating peptide/protein concentration

7.3.2.3Calculating peptide/protein concentration

The concentration of peptide or protein in the original sample can be calculated from the sum of the products of the number of picomoles of each amino acid multiplied by its corresponding molecular weight.

Using the example cited in the table from Section 7.3.1, the calculation begins as follows:

Example calculation:

For Asp (asparagine) in the sample: 220 picomoles observed with a molecular weight for the amino acid of 133.10 g/mole gives the following:

This same calculation is applied for each desired amino acid. The table below shows the calculated picograms for each amino acid, with the sum total of picograms protein injected from the sample in the lower right.

7.4 QUANTITATION OF AMINO ACIDS IN FEEDS

7.4 QUANTITATION OF AMINO ACIDS IN FEEDS

In the analysis of food and feeds, the above-mentioned calculated values also apply. However, the more important information for most feed analyses is the content of specific, growth-limiting amino acids, such as methionine and cysteine. The value most commonly of concern is the % amino acid content by weight in the sample.

7.4.1 Calculating % weight of amino acid in food/feed

7.4.1 Calculating % weight of amino acid in food/feed

To calculate the % by weight of an amino acid:

Example calculation:

Step 1: Convert reported molar amino acid concentrationtoreported weight (g/mL).

Step 1: Convert reported molar amino acid concentrationtoreported weight (g/mL).

The reported value of Amount (pmol/µL) must be multiplied by the Residue MW (gm/mol) and any conversion factors.

Step 2: Convert the reported weight of each amino acid to weight.

Step 2: Convert the reported weight of each amino acid to weight.

The reported amount in g/mol is then multiplied by any dilution factors. The result is then divided by the weight of the sample, and then multiplied by 100 to convert to a percent.

Example calculation:

Where:

Amount = amount of amino acid in g/mL

Dilution = dilution of sample

Step 3: Convert the reported weight of each amino acid %weight.

Step 3: Convert the reported weight of each amino acid %weight.

Sample weight = weight in mg

7.4.2 The official AOAC Method 994.12 Amino Acids in Feed: calculation of the weight % amino acid in the sample

7.4.2 The official AOAC Method 994.12 Amino Acids in Feed: calculation of the weight % amino acid in the sample

This method requires the use of an internal standard.

Example calculation:

Step 1: Calculate a response factor (RFaa)for each amino acid.

Step 1: Calculate a response factor (RFaa)for each amino acid.

The peak area for the internal standard is multiplied by the weight of the amino acid in mg. This is then divided by the result of multiplying the peak area of the amino acid by the weight of internal standard.

Where:

RFaa= response factor for the amino acid

Pn= peak area for internal standard

Paa= peak area for the amino acid in the sample

Waa= weight of the amino acid in mg

Wn= weight of internal standard in mg

Step 2: Calculate an Internal Standard (IS) factor.

Step 2: Calculate an Internal Standard (IS) factor.

Step 3: Determine the % amino acids in weight.

Step 3: Determine the % amino acids in weight.

The % content calculation begins with the multiplication of the peak area of the amino acid by the calculated response factor. This is then multiplied by the internal standard factor. This number then is divided by the multiplicand of the peak area of the internal standard and the weight of the sample analyzed. This is then converted to a percent.

Where:

Paa= peak area of amino acid

Pn= peak area of internal standard

RFaa= calculated response factor

IS = calculated internal standard factor

Example:

For an amino acid in a feed sample, the following values were determined:

Weight of amino acid (Waa) = 0.5 mg

Peak area of amino acid (Paa) = 100,000

Peak area of internal standard (Pn) = 110,000

Weight of internal standard (Wn) = 0.5 mg

Weight of test portion (Ws) = 10 mg

Step 1:Calculate the response factor, RFaa:

Step 1:Calculate the response factor, RFaa:

Step 2:Calculate the internal standard factor, IS:

Step 2:Calculate the internal standard factor, IS:

0.5mgx 2 x 10-2= 0.05

Step 3:With both values calculated, the % amino acid can be determined:

Step 3:With both values calculated, the % amino acid can be determined:

The amino acid of concern is present at a level of 0.9% by weight of the feed.

Related

AccQ•Tag Ultra, AccQ•Tag and Pico•Tag Columns

Enable your laboratory to obtain accurate amino acid composition from protein/peptide hydrolysates, physiologic fluids, feeds, foods, pharmaceutical preparations, and myriad other samples using traditional HPLC or UHPLC instrumentation.

Accurately separate, identify, & quantify amino acids in cell culture, protein hydrolysates, foods, and feeds with Waters AccQ•Tag and AccQ•Tag Ultra Amino Acid Analysis standards and kits for HPLC, UHPLC, and UPLC.

Amino Acid AnalysisSolutions

Waters offers three distinctively reliable methods for accurate amino acid analyses. All three utilize pre-column derivatization methods followed by reversed-phase chromatography with on-line detection of well resolved peaks using either UV absorbance or fluorescence detection.

Automation Workflow Kits and Scripts

Realize the full potential of your automation workstations with Waters sample preparation kits, and seamlessly automate your Waters workflow to gain laboratory efficiency.

Quantitation of Amino Acids (2024)
Top Articles
Latest Posts
Recommended Articles
Article information

Author: Ms. Lucile Johns

Last Updated:

Views: 5667

Rating: 4 / 5 (61 voted)

Reviews: 92% of readers found this page helpful

Author information

Name: Ms. Lucile Johns

Birthday: 1999-11-16

Address: Suite 237 56046 Walsh Coves, West Enid, VT 46557

Phone: +59115435987187

Job: Education Supervisor

Hobby: Genealogy, Stone skipping, Skydiving, Nordic skating, Couponing, Coloring, Gardening

Introduction: My name is Ms. Lucile Johns, I am a successful, friendly, friendly, homely, adventurous, handsome, delightful person who loves writing and wants to share my knowledge and understanding with you.